[ Pobierz całość w formacie PDF ]
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
8.6 Model Studies for Flows without FreeSurface
Effects
Freesurface effects are absent in the flow of liquids or gases in closed conduits, including control devices such
as valves, or in the flow about bodies (e.g., aircraft) that travel through air or are deeply submerged in a liquid
such as water (submarines). Freesurface effects are also absent where a structure such as a building is stationary
and wind flows past it. In all these cases, given relatively low Mach numbers, the Reynoldsnumber criterion is
the most significant for dynamic similarity. That is, the Reynolds number for the model must equal the Reynolds
number for the prototype.
Example 8.4 illustrates the application of Reynoldsnumber similitude for the flow over a blimp.
EXAMPLE 8.4 REYOLDSUMBER SIMILITUDE
The drag characteristics of a blimp 5 m in diameter and 60 m long are to be studied in a wind tunnel.
If the speed of the blimp through still air is 10 m/s, and if a 1/10 scale model is to be tested, what
airspeed in the wind tunnel is needed for dynamically similar conditions? Assume the same air
pressure and temperature for both model and prototype.
PROBLEM DEFINITION
Situation:
Wind tunnel test of a 1/10 scale model blimp. Prototype speed is 10 m/s.
Find:
Speed (in m/s) in wind tunnel for dynamic similitude.
Assumptions:
Same air pressure and temperature for model and prototype, therefore ν
M
= ν
P
.
PLAN
The only πgroup that is appropriate is the Reynolds number (there are no compressibility effects,
freesurface effects, or gravitation effects). Thus equating the model and prototype Reynolds number
satisfies dynamic similitude.
1. Equate the Reynolds number of the model and the prototype.
2. Calculate model speed.
SOLUTION
1. Reynoldsnumber similitude
2. Model velocity
1 of 4
1/15/2009 12:49 AM
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
Example 8.4 shows that the airspeed in the wind tunnel must be 100 m/s for true Reynoldsnumber similitude.
This speed is quite large, and in fact Machnumber effects may start to become important at such a speed.
However, it will be shown in Section 8.9 that it is not always necessary to operate models at true Reynolds
number similitude to obtain useful results.
If the engineer feels that it is essential to maintain Reynoldsnumber similitude, then only a few alternatives are
available. One way to produce high Reynolds numbers at nominal airspeeds is to increase the density of the air.
A NASA wind tunnel at the Ames Research Center at Moffett Field in California is one such facility. It has a
12 ft—diameter test section; it can be pressurized up to 90 psia (620 kPa); it can be operated to yield a Reynolds
number per foot up to 1.2 × 10
7
, and the maximum Mach number at which a model can be tested in this wind
tunnel is 0.6. The airflow in this wind tunnel is produced by a singlestage, 20blade axialflow fan, which is
powered by a 15,000horsepower, variablespeed, synchronous electric motor 3. There are several problems that
are peculiar to a pressurized tunnel. First, a shell (essentially a pressurized bottle) must surround the entire tunnel
and its components, adding to the cost of the tunnel. Second, it takes a long time to pressurize the tunnel in
preparation for operation, increasing the time from the start to the finish of runs. In this regard it should be
noted that the original pressurized wind tunnel at the Ames Research Center was built in 1946; however, because
of extensive use, the tunnel's pressure shell began to deteriorate, so a new facility (the one previously described)
was built and put in operation in 1995. Improvements over the old facility include a better data collection
system, very low turbulence, and capability of depressurizing only the test section instead of the entire
620,000 ft
3
wind tunnel circuit when installing and removing models. The original pressurized wind tunnel was
used to test most models of U.S. commercial aircraft over the past halfcentury, including the Boeing 737, 757,
and 767; Lockheed L1011; and McDonnell Douglas DC9 and DC10.
The Boeing 777 was tested in the lowspeed, pressurized 5 m—by—5 m tunnel in Farnborough, England. This
tunnel, operated by the Defence Evaluation and Research Agency (DERA) of Great Britain, can operate at three
atmospheres with Mach numbers up to 0.2. Approximately 15,000 hours of total testing time was required for
the Boeing 777 4.
Another method of obtaining high Reynolds numbers is to build a tunnel in which the test medium (gas) is at a
very low temperature, thus producing a relatively highdensity—lowviscosity fluid. NASA has built such a
tunnel and operates it at the Langley Research Center. This tunnel, called the National Transonic Facility, can be
pressurized up to 9 atmospheres. The test medium is nitrogen, which is cooled by injecting liquid nitrogen into
the system. In this wind tunnel it is possible to reach Reynolds numbers of 10
8
based on a model size of 0.25 m
5. Because of its sophisticated design, its initial cost of approximately $100,000,000 6, and its operating expenses
are high.
Another modern approach in windtunnel technology is the development of magnetic or electrostatic suspension
of models. The use of the magnetic suspension with model airplanes has been studied 6, and the electrostatic
suspension for the study of singleparticle aerodynamics has been reported 7.
The use of wind tunnels for aircraft design has grown significantly as the size and sophistication of aircraft have
increased. For example, in the 1930s the DC3 and B17 each had about 100 hours of windtunnel tests at a rate
of $100 per hour of run time. By contrast the F15 fighter required about 20,000 hours of tests at a cost of
$20,000 per hour 6. The latter test time is even more staggering when one realizes that a much greater volume of
data per hour at higher accuracy is obtained from the modern wind tunnels because of the highspeed data
acquisition made possible by computers.
Example 8.5 illustrates the use of Reynoldsnumber similitude to design a test for a valve.
2 of 4
1/15/2009 12:49 AM
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
EXAMPLE 8.5 REYOLDSUMBER SIMILITUDE OF A
VALVE
The valve shown is the type used in the control of water in large conduits. Model tests are to be done,
using water as the fluid, to determine how the valve will operate under wideopen conditions. The
prototype size is 6 ft in diameter at the inlet. What flow rate is required for the model if the prototype
flow is 700 cfs? Assume that the temperature for model and prototype is 60°F and that the model inlet
diameter is 1 ft.
Sketch:
Situation:
A 1/6 scale model of valve tested in water tunnel. Prototype flow rate is 700 cfs.
Find:
Flow rate through model.
Assumptions:
1. No compressibility, free surface or gravitational effects.
2. Temperature of water in model and prototype is the same. Therefore kinematic viscosity of
model and prototype are equal.
PLAN
Dynamic similitude is obtained by equating the model and prototype Reynolds number. The
model/prototype area ratio is the square of the scale ratio.
1. Equate Reynolds number of model and prototype.
2. Calculate the velocity ratio.
3. Calculate the discharge ratio using model/prototype area ratio.
SOLUTION
1. Reynoldsnumber similitude
3 of 4
1/15/2009 12:49 AM
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
2. Velocity ratio
Since ν
P
= ν
M
,
3. Discharge
REVIEW
This discharge is very large and serves to emphasize that very few model studies are made that
completely satisfy the Reynoldsnumber criterion. This subject will be discussed further in the next
sections.
Copyright ¨ 2009 John Wiley & Sons, Inc. All rights reserved.
4 of 4
1/15/2009 12:49 AM
[ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl jajeczko.pev.pl
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
8.6 Model Studies for Flows without FreeSurface
Effects
Freesurface effects are absent in the flow of liquids or gases in closed conduits, including control devices such
as valves, or in the flow about bodies (e.g., aircraft) that travel through air or are deeply submerged in a liquid
such as water (submarines). Freesurface effects are also absent where a structure such as a building is stationary
and wind flows past it. In all these cases, given relatively low Mach numbers, the Reynoldsnumber criterion is
the most significant for dynamic similarity. That is, the Reynolds number for the model must equal the Reynolds
number for the prototype.
Example 8.4 illustrates the application of Reynoldsnumber similitude for the flow over a blimp.
EXAMPLE 8.4 REYOLDSUMBER SIMILITUDE
The drag characteristics of a blimp 5 m in diameter and 60 m long are to be studied in a wind tunnel.
If the speed of the blimp through still air is 10 m/s, and if a 1/10 scale model is to be tested, what
airspeed in the wind tunnel is needed for dynamically similar conditions? Assume the same air
pressure and temperature for both model and prototype.
PROBLEM DEFINITION
Situation:
Wind tunnel test of a 1/10 scale model blimp. Prototype speed is 10 m/s.
Find:
Speed (in m/s) in wind tunnel for dynamic similitude.
Assumptions:
Same air pressure and temperature for model and prototype, therefore ν
M
= ν
P
.
PLAN
The only πgroup that is appropriate is the Reynolds number (there are no compressibility effects,
freesurface effects, or gravitation effects). Thus equating the model and prototype Reynolds number
satisfies dynamic similitude.
1. Equate the Reynolds number of the model and the prototype.
2. Calculate model speed.
SOLUTION
1. Reynoldsnumber similitude
2. Model velocity
1 of 4
1/15/2009 12:49 AM
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
Example 8.4 shows that the airspeed in the wind tunnel must be 100 m/s for true Reynoldsnumber similitude.
This speed is quite large, and in fact Machnumber effects may start to become important at such a speed.
However, it will be shown in Section 8.9 that it is not always necessary to operate models at true Reynolds
number similitude to obtain useful results.
If the engineer feels that it is essential to maintain Reynoldsnumber similitude, then only a few alternatives are
available. One way to produce high Reynolds numbers at nominal airspeeds is to increase the density of the air.
A NASA wind tunnel at the Ames Research Center at Moffett Field in California is one such facility. It has a
12 ft—diameter test section; it can be pressurized up to 90 psia (620 kPa); it can be operated to yield a Reynolds
number per foot up to 1.2 × 10
7
, and the maximum Mach number at which a model can be tested in this wind
tunnel is 0.6. The airflow in this wind tunnel is produced by a singlestage, 20blade axialflow fan, which is
powered by a 15,000horsepower, variablespeed, synchronous electric motor 3. There are several problems that
are peculiar to a pressurized tunnel. First, a shell (essentially a pressurized bottle) must surround the entire tunnel
and its components, adding to the cost of the tunnel. Second, it takes a long time to pressurize the tunnel in
preparation for operation, increasing the time from the start to the finish of runs. In this regard it should be
noted that the original pressurized wind tunnel at the Ames Research Center was built in 1946; however, because
of extensive use, the tunnel's pressure shell began to deteriorate, so a new facility (the one previously described)
was built and put in operation in 1995. Improvements over the old facility include a better data collection
system, very low turbulence, and capability of depressurizing only the test section instead of the entire
620,000 ft
3
wind tunnel circuit when installing and removing models. The original pressurized wind tunnel was
used to test most models of U.S. commercial aircraft over the past halfcentury, including the Boeing 737, 757,
and 767; Lockheed L1011; and McDonnell Douglas DC9 and DC10.
The Boeing 777 was tested in the lowspeed, pressurized 5 m—by—5 m tunnel in Farnborough, England. This
tunnel, operated by the Defence Evaluation and Research Agency (DERA) of Great Britain, can operate at three
atmospheres with Mach numbers up to 0.2. Approximately 15,000 hours of total testing time was required for
the Boeing 777 4.
Another method of obtaining high Reynolds numbers is to build a tunnel in which the test medium (gas) is at a
very low temperature, thus producing a relatively highdensity—lowviscosity fluid. NASA has built such a
tunnel and operates it at the Langley Research Center. This tunnel, called the National Transonic Facility, can be
pressurized up to 9 atmospheres. The test medium is nitrogen, which is cooled by injecting liquid nitrogen into
the system. In this wind tunnel it is possible to reach Reynolds numbers of 10
8
based on a model size of 0.25 m
5. Because of its sophisticated design, its initial cost of approximately $100,000,000 6, and its operating expenses
are high.
Another modern approach in windtunnel technology is the development of magnetic or electrostatic suspension
of models. The use of the magnetic suspension with model airplanes has been studied 6, and the electrostatic
suspension for the study of singleparticle aerodynamics has been reported 7.
The use of wind tunnels for aircraft design has grown significantly as the size and sophistication of aircraft have
increased. For example, in the 1930s the DC3 and B17 each had about 100 hours of windtunnel tests at a rate
of $100 per hour of run time. By contrast the F15 fighter required about 20,000 hours of tests at a cost of
$20,000 per hour 6. The latter test time is even more staggering when one realizes that a much greater volume of
data per hour at higher accuracy is obtained from the modern wind tunnels because of the highspeed data
acquisition made possible by computers.
Example 8.5 illustrates the use of Reynoldsnumber similitude to design a test for a valve.
2 of 4
1/15/2009 12:49 AM
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
EXAMPLE 8.5 REYOLDSUMBER SIMILITUDE OF A
VALVE
The valve shown is the type used in the control of water in large conduits. Model tests are to be done,
using water as the fluid, to determine how the valve will operate under wideopen conditions. The
prototype size is 6 ft in diameter at the inlet. What flow rate is required for the model if the prototype
flow is 700 cfs? Assume that the temperature for model and prototype is 60°F and that the model inlet
diameter is 1 ft.
Sketch:
Situation:
A 1/6 scale model of valve tested in water tunnel. Prototype flow rate is 700 cfs.
Find:
Flow rate through model.
Assumptions:
1. No compressibility, free surface or gravitational effects.
2. Temperature of water in model and prototype is the same. Therefore kinematic viscosity of
model and prototype are equal.
PLAN
Dynamic similitude is obtained by equating the model and prototype Reynolds number. The
model/prototype area ratio is the square of the scale ratio.
1. Equate Reynolds number of model and prototype.
2. Calculate the velocity ratio.
3. Calculate the discharge ratio using model/prototype area ratio.
SOLUTION
1. Reynoldsnumber similitude
3 of 4
1/15/2009 12:49 AM
Model Studies for Flows without FreeSurface Effects
http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...
2. Velocity ratio
Since ν
P
= ν
M
,
3. Discharge
REVIEW
This discharge is very large and serves to emphasize that very few model studies are made that
completely satisfy the Reynoldsnumber criterion. This subject will be discussed further in the next
sections.
Copyright ¨ 2009 John Wiley & Sons, Inc. All rights reserved.
4 of 4
1/15/2009 12:49 AM
[ Pobierz całość w formacie PDF ]